 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| NTE222 Field Effect Transistor Dual Gate N-Channel MOSFET Absolute Maximum Ratings: Drain-Source Voltage, VDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25V Drain-Gate Voltage, VDG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30V Drain Current, ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50mA Reverse Gate Current, IG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -10mA Forward Gate Current, IGF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10mA Total Device Dissipation (TA = +25C), PD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 360mW Derate Above 25C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4mW/C Total Device Dissipation (TC = +25C), PD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2mW Derate Above 25C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.8mW/C Operating Junction Temperature Range, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65 to +175C Storage Temperature Range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65 to +175C Lead Temperature (During Soldering), TL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +300C Electrical Characteristics: (TA = +25C unless otherwise specified) Parameter OFF Characteristics Drain-Source Breakdown Voltage Gate 1-Source Breakdown Voltage Gate 2-Source Breakdown Voltage Gate 1 Leakage Current Gate 2 Leakage Current Gate 1 to Source Cutoff Voltage Gate 2 to Source Cutoff Voltage ON Characteristics (Note 2) Zero-Gate-Voltage Drain Current Small-Signal Characteristics Forward Transfer Admittance |Yfs| VDS = 15V, VG2S = 4V, VG1S = 0V, f = 1kHz, Note 3 10 - 22 mmhos IDSS VDS = 15V, VG2S = 4V, VG1S = 0V 6 - 30 mA V(BR)DSX ID = 10A, VG1 = VG2 = -5V 25 6 6 - - -0.5 -0.2 - - - - - - - - 30 30 10 10 -4.0 -4.0 V V V nA nA V V V(BR)G1SO IG1 = 10mA, Note 1 V(BR)G2SO IG2 = 10mA, Note 1 IG1SS IG2SS VG1S(off) VG2S(off) VG1S = 5V, VG2S = VDS = 0 VG2S = 5V, VG1S = VDS = 0 VDS = 15V, VG2S = 4V, ID = 20A VDS = 15V, VG1S = 0V, ID = 20A Symbol Test Conditions Min Typ Max Unit Note 1. All gated breakdown voltages are measured while the device is conducting rated gate current. This insures that the gate voltage limiting network is functioning properly. Note 2. Pulse Test: Pulse Width = 30s, Duty Cycle 2%. Note 3. This parameter must be measured with bias voltages applied for less than five (5) seconds to avoid overheating. Electrical Characteristics (Cont'd): (TA = +25C unless otherwise specified) Parameter Symbol Test Conditions Min Typ Max Unit Small-Signal Characteristics (Cont'd) Input Capacitance Reverse Transfer Capacitance Output Capacitance Functional Characteristics Noise Figure NF VDD = 18V, VGG = 7V, f = 200MHz VDD = 15V, VG2S = 4V, ID = 10mA, f = 200MHz Common Source Power Gain Gps VDD = 18V, VGG = 7V, f = 200MHz VDD = 15V, VG2S = 4V, ID = 10mA, f = 200MHz Bandwidth BW VDD = 18V, VGG = 7V, f = 200MHz VDD = 18V, fLO = 245MHz, fRF = 200MHz, Note 5 Gain Contol Gate-Supply Voltage VGG(GC) VDD = 18V, Gps = 300dB, f = 200MHz, Note 4 - - 20 14 7 4 0 - - - - - - - 3.5 5.0 28 - 12 7 -2.0 dB dB dB dB MHz MHz V Ciss Crss Coss VDS = 15V, VG2S = 4V, ID = IDSS, f = 1MHz VDS = 15V, VG2S = 4V, ID = 10mA, f = 1MHz VDS = 15V, VG2S = 4V, ID = IDSS, f = 1MHz - 0.005 - 3.3 - 1.4 - 0.03 - pF pF pF Note 4. Gps is defined as the change in Gps from the value at VGG = 7V. Note 5. Amplitude at input from local oscillator is 3V RMS. .220 (5.58) Dia .185 (4.7) Dia .190 (4.82) .030 (.762) .500 (12.7) Min .018 (0.45) Dia Gate 2 Drain Gate 1 45 Source/Case .040 (1.02) |
Price & Availability of NTE222
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |